Separate names with a comma.
Have a 68 Shelby 500 428 C.I. engine single set of points . Anyone tell me what to set the points at. The original owners manual says .021 The...
Have a '68 GT500....no rear brake lights on both sides. No rear Hazard lights flash. Front Parking lights do flash. The 2 green arrows on the...
on each side , were the brake line comes into the back of the drum . what looks like a grease fitting . I never noticed this before ,Should that...
Have a '68 500. With headlights switch on, tail lights work both sides. Brake pedal, hazard lights, right side directional signal does not...
Have a 428- PI, Plugs call for a # BF 32 Autolite . All I can get is # 45 autolite that come with no washers. Is their any diff. in the heat range...
Is the master cylinder suppose to be very close to the valve cover, all most touching it at times ? The V.C. has some paint scratch marks on it,...
Have a '68 500 FB some 14 years now. The tire I use for the spare, the PO said it was one of the originals....don't know. The raised white...
On Ford Muscle "Timing is Everything" it says counterclockwise to decrease advance & clockwise to advance on vac .aftermarket units. On Mustangs &...
My Shelby was built on 1-29 68,--19 days late. With 68 production of all Mustangs starting sometime in Oct.- Nov. of 67, how could they produce...
I google 68 GT 500 & click on images on page 2. I saw a gold Shelby, clicked on that page & clicked again for a full size picture. That's my car...
According to the Marti report , Sunlit Gold [ Y ] Ford Paint # 3073-A & the Mustang Detailing Guide of 1995, gives the # A E 60 3216 . I would...
Is there any difference between a 68 G.T. Galaxie 428 Q code & the 428 P.I. S code engines ? --Thanks,---S.
On a 68 P.I. what color were the dis. brakes originally .Thanks--S.
I have a 68 P.I. with a build date of Jan. 11 -68 . The # stamped on the block , below the head reads 8 A 11 N What does the letter N stand...
On a 68 P.I. did the springs come with a pair of insulators & retainer ? One goes between the bottom of the axle & the top of the spring, the...
If the 68 P.I. is considered over carb. with a 735, then what about the 67 P.I. with dual 600 carbs ? Wouldn't that run alot worse than the...
On a 68-428, P.I. did they come with a carb. Spacer ? & also, if they did, what size would it be.---Thanks,---S.
on a 68-500. Do any of you guys use gasket cement on cork gaskets when installing the valve covers.?? I did this a couple of times in the past,...
the new version, with the 007 guy. Got a quick look at one scene what I thought was a jeep with fog lights on the roll bar. It turned out to be a...
Check this out....very interesting!....S http://www.jaylenosgarage.com/
I'm assuming something, could be wright or wrong I don't know. When looking at a 68 K.R. high Shelby ser. #-- 3800--4000 vin # in the 211000...
were they only for Shelbys .? I have seen what looked to be the same, on G.M.car [ advertisments ] & some 67-8 4 door thunderbirds . The mag in...
Does anyone know what the octane rating on prem. fuel that was required for the 428 P.I. in 1968. I'm trying to get a mixture down , so that I'm...
Is the " North Texas Mustang Club " still active ? And does anyone have an E-Mail address that I could contact Thanks,---S.
My 68 int. door panels, the plasic chrome trim pcs . Are kind of flaking off after 38 years . Can they be bought from a vender ? Or does it have...